Sanding: grit sequence, technique and when to stop
Where to start, which grits to use and not skip, how to sand with a random-orbit sander and by hand, raising the grain, and the right final grit for your finish.
Sanding is the step most people rush and most finishes reveal. Each grit exists to remove the scratches left by the one before it. Skip a grit, press too hard or stop too early, and the scratches reappear the moment stain or finish goes on.
Where to start
Start with the finest grit that removes the defects you have:
- Freshly planed or scraped surfaces: start at 120 or even 150. A sharp plane leaves a better surface than coarse sandpaper.
- Machine marks, light tearout, glue residue: start at 100 or 120.
- Heavy tearout, uneven glued-up panels: 80, but flatten the panel first; sandpaper is a slow way to fix a panel that is out of flat. See edge-gluing a panel.
Starting coarser than needed only makes more scratches to remove.
Don’t skip grits
A typical sequence is 80, 120, 150, 180. Moving up by more than about half the previous grit number leaves the finer paper unable to remove the deeper scratches in reasonable time. Going from 80 straight to 180 looks smooth to the hand and shows swirls under finish.
Two checks before moving up a grit:
- Pencil marks. Scribble lightly across the surface and sand until they are all gone. That surface has been fully worked at this grit.
- Raking light. A light held low across the surface shows scratches and swirls that overhead light hides.
Random-orbit technique
- Let the sander’s weight do the work. Pressing down slows the pad’s rotation and makes deeper, curly swirl marks.
- Move slowly, about an inch per second, in overlapping passes.
- Keep the pad flat. Tilting it to “focus” on a spot digs a hollow.
- Start and stop the sander on the work, not in the air above it, to avoid gouging.
- Vacuum or wipe the surface between grits. A stray coarse grain from the previous paper leaves a scratch at the next.
- Change paper when it stops cutting. Dull paper burnishes rather than cuts.
By hand
Finish with a light hand-sanding pass along the grain at the final grit, using a flat block on flat surfaces. It removes any faint swirl the orbital sander left and aligns the remaining scratches with the grain, where they are least visible.
Card scrapers and smoothing planes are faster than sandpaper on many hardwoods and leave a crisp surface. Many makers scrape or plane and then sand only the final grit.
The final grit
- Film finishes (varnish, polyurethane, lacquer): 180 is usually plenty; the finish fills finer scratches.
- Oil finishes: 180 to 220.
- Stain: stop at 150 to 180. Sanding much finer burnishes the surface and reduces how much stain it absorbs, which can make colour lighter or uneven.
- End grain: sand one or two grits finer than the faces. End grain absorbs more stain and finish and darkens more.
Whatever you choose, sand every surface of a piece to the same final grit so the finish looks even. Test the whole sequence on an offcut from the same boards.
Raising the grain
Water-based finishes and stains swell loose wood fibres, leaving the surface fuzzy after the first coat. Prevent it by raising the grain beforehand: wipe the sanded surface with a damp cloth, let it dry fully, then sand lightly with the final grit to cut the raised fibres off.
Edges and corners
Sharp edges chip and do not hold finish well. Break every edge with a couple of light passes of fine paper on a block, or a small chamfer or roundover, before finishing. Be careful near veneered plywood edges and on thin veneers, where it is easy to sand through.
Before assembly
Sanding inside corners after assembly is awkward. Sand interior faces of parts, such as the inside of aprons, legs and drawer sides, before glue-up, keeping the joint surfaces themselves unsanded so they still fit. See glue-ups.
Dust
Connect the sander to a vacuum or dust extractor, and wear a mask. Fine sanding dust is the hardest to see and the most harmful to breathe.
Related: milling rough lumber, choosing a wood species.
Numbers here are starting points from common shop practice and published references. Check your own stock, tools and hardware instructions, and cut a test piece before committing project wood. Spotted an error? The contact address is on the About page.
Keep reading
GrainDraft is a free woodworking design tool that runs in your browser. Open GrainDraft